Opening the Siemens Surpresso Compact

Written By: VauWeh
  • Comments: 6
Opening the Siemens Surpresso Compact

Difficulty

Easy

Steps

6

Time Required

No estimate

Introduction

For almost any repair the device will need to be opened first. The opening procedure ist described in this guide.

These instructions may also help with other Siemens/Bosch models and with coffee makers from Nivona, Melitta, and Miele—they have a very similar design.

  1. Q2UPhfbroAeCRfjS

    • Unplug your coffee maker!

    • Remove the water container, the brew group and the drip tray with pomace container.

    • Using a spoon, remove as much of the coffee beans as possible from the coffee bean container.

    • Depending on the model, additional sensors with cables may be installed on the top and side panels. You have to remove these before you can completely remove the housing parts.

  2. yF2VMwCAhSYxPkG1

    • Remove the two Torx T10 screws on the top.

  3. wTT1MpMmEjmUIynE
    wTT1MpMmEjmUIynE
    1AFpHWHpntCbNZIX

    • Remove seven T10 Torx screws on the back.

    • The two screws at the bottom of the front can remain.

  4. jkOwWpZsuusJbE3D
    jkOwWpZsuusJbE3D
    glZfhxrNfcwdSvdU

    • Press with a flat-head screwdriver into the openings on the side with the water tank. This releases the latches on the top.

    • Press the flat-head screwdriver into the opening on the side with the brew group. This will release the last notch on the top.

    • Lift the top off.

    • On some models, a cable leads to the sensor on the powder tray. Unplug the connector on this cable first.

  5. 1VbYWBXIxBHNcVLU
    1VbYWBXIxBHNcVLU
    Q6GWtciub3TxDI2e

    • Slide the side section of the brewing unit about 2 cm to the rear. This sometimes gets stuck and may require some force to remove.

    • Remove the two tabs from the power switch.

    • Take off the side panel with the brew group.

  6. QnnxnVCl3aNFk3Ms

    • Do the same with the panel on the other side.

    • To remove the water tank hose simply pull it of the pump.

    • Remove the side panel.

    Hallo, das ja ganz tolĺ erklärt. Ich brauchte ein Bild von dem Elektronicteil wo man die Kabel sieht in welcher Buchsen Sie stecken.Danke.

    Bernd Bennewitz -

    Bei den anderen Anleitungen vielleicht, z.B. der hier: Siemens Surpresso Compact microswitches in the gear drive replacement, Schritt 10 ?

    VauWeh -

Conclusion

To reassemble your device, follow the steps in reverse order.

Author

VauWeh

Member since: 19/10/15

234423 Reputation

4 comments

Sehr gut beschrieben und bebildert, danach kann man gut arbeiten, Danke.

h.kornetzki -

Wie bekomme ich den vorderen Gehäusedeckel ab? Ich muss den Dampfschalter tauschen.

sabine.gorski -

Hab ich noch nie gemacht. Sicher muss der Auslauf weg: Siemes Surpresso Compact coffee outlet Replacement, suche dann die Schrauben und Rasten. Gutes Gelingen, wir würden uns freuen, wenn du das für iFixit dokumentierst!

VauWeh -

Super Anleitung! Danach war es ein Leichtes, die Maschine zu zerlegen.

Micha Maier -