iPhone 16 Pro LiDAR Sensor Removal

Written By: Nick Schultz
  • Comments: 3
iPhone 16 Pro LiDAR Sensor Removal

Difficulty

Moderate

Steps

7

Time Required

1 - 2 hours

Introduction

Follow this guide to replace the LiDAR sensor in your iPhone 16 Pro.

After you complete this guide, calibrate an authentic Apple LiDAR sensor using Repair Assistant.

You'll need replacement back glass adhesive to complete this repair.

  1. K4AWsftcl4n5BtIp
    K4AWsftcl4n5BtIp
    aFo1CdHnjZVIyeaI

    • Allow the phone's battery to drain below 25%, as a charged lithium-ion battery is a potential safety hazard.

    • Unplug any cables from the phone.

    • Hold the power and either volume buttons and slide to power off the phone.

    Wilson Demosthène

    Demosthène Wilson -

  2. EmBlBsGeBABlcwlv
    EmBlBsGeBABlcwlv
    ptNWZaLIy4EsKrcf

    • If the screen or back glass is badly cracked, lay overlapping strips of packing tape over the glass to protect yourself and make disassembly easier.

    • Make sure there's a smooth area near the bottom edge that's big enough for a suction cup to stick to.

  3. 2L1xyPNHbxcHDGo2
    2L1xyPNHbxcHDGo2
    pHlXkMHcKaCfppXs
    UyUfMfOFG1QtVZl1

    • If inserted too far, an opening pick can damage your device. Follow this step to mark your pick and prevent damage.

    • Measure 3 mm from the tip and mark the opening pick with a permanent marker.

    • You can also mark the other corners of the pick with different measurements.

    • Alternatively, tape a coin to a pick 3 mm from the tip.

  4. 4wwMsFG3yVDMQZim
    4wwMsFG3yVDMQZim
    jXnDR5btQ4VuGNTl

    • Use a P2 pentalobe screwdriver to remove the two 7.4 mm‑long screws on either side of the USB-C port.

  5. iVSOLGyLuByyRwfT
    iVSOLGyLuByyRwfT
    pL4xlCcxSXVyDEnc
    XcAo6vW1HZdFHFQ4

    • Use the point of a spudger to pry up and disconnect the LiDAR sensor press connector.

    First picture is incorrect, it's the connector underneath.

    Oliver -

    Good catch, thank you!

    Nick Schultz -

  6. PCyyuTmCSIGGNYP5
    PCyyuTmCSIGGNYP5
    HjF2uJxy1IO1HBtT

    • Use a Phillips screwdriver to remove the two screws securing the LiDAR sensor:

    • One 1.7 mm‑long screw

    • One 3.0 mm‑long screw

  7. jTCqKxvpFhkYNVXh
    jTCqKxvpFhkYNVXh
    OR1YhtvsXxwPNJIR

    • Use your fingers or tweezers to lift and remove the LiDAR sensor.

Conclusion

To reassemble your iPhone, follow these instructions in reverse order.

After your repair, calibrate a genuine replacement LiDAR sensor using Apple's Repair Assistant. Navigate to Settings → General → About → Parts & Service History, tap Restart & Finish Repair, and follow the onscreen prompts.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our iPhone 16 Pro Answers community for help.

Author

Nick Schultz

Member since: 24/03/24

20083 Reputation

0 comments