Ozeino OW810 Headband Cushion Replacement

Written By: Rylee
  • Comments: 4
Ozeino OW810 Headband Cushion Replacement

Difficulty

Very difficult

Steps

42

Time Required

45 minutes

Introduction

If you are experiencing issues with your Ozeino OW810 headband cushion or just find yourself wanting to replace it, use this guide to help.

The headband cushion helps protect the top of the head from the harshness of the plastic head piece. This guide gives you step by step directions on how to take the headset apart and remove the cushion.

Before following this guide review the prerequisite guides, they go into more detail about the initial taking apart sequence.

  1. 2m3Zc1EsU2loDHd1

    • Insert a nylon spudger in the seam between the right ear pad and the driver housing.

    • Pry the right ear pad off.

  2. 4wOPduSyU1KORpIv

    • Use a Phillips #000 screwdriver to remove the six 3.2 mm screws securing the right driver housing.

  3. Q2idXsvLCH4Y4B2B

    • Lift the driver housing off, with care not to strain the connected cables.

  4. qQMPEghnEfRXDPEL

    • Use a nylon spudger to gently pry out the battery.

    • Do not use a metal spudger to pry out the battery. Metal spudgers can easily puncture the battery.

  5. pOTsvmmXtVw2ExVa

    • Remove tape from the battery.

    • Pull the circuit board up along with the wiring from either side.

    • Replace battery.

    Be more concise about pulling the wiring. Is it pulling the circuit board with the battery? Other than that this is easy to understand and looks great!

    Morgan G -

  6. jOekARMILUsSEH6H

    • Use a Metal Spudger to remove the ear muffs from the headset.

  7. BUXrOiRD3EkBHLEg

    • Using a Phillips #000 screwdriver, remove the 1st 9mm screw that secures the left head piece.

  8. OTMD1HnCuAXUSCPE

    • Using a Phillips #000 screwdriver, remove the 2nd 9mm screw that secures the left head piece.

  9. J3ROlfHpJaFRaLJU

    • Using a Phillips #000 screwdriver, remove the 3rd 9mm screw that secures the left head piece.

  10. 2exxXDNyOCj2aH1i

    • Using a Phillips #000 screwdriver, remove the 4th 9mm screw that secures the left head piece.

  11. RuDICFPgYG1qWAKW

    • Using a Phillips #000 screwdriver, remove the 5th 9mm screw that secures the left head piece.

  12. mj54IuYaWUdYHYxi

    • Using a Phillips #000 screwdriver, remove the last 9mm screw that secures the left head piece.

  13. G4tnKiBfFSBpSwwB

    • Use your hands or the metal spudger to pry open the earpiece to find the green panel.

  14. hUiWMM4VpmUDJaaQ

    • After opening the ear piece find the green panel and look for the 1st 7mm screw. Use the Phillips #000 screwdriver to remove the screw that is holding the green panel in place.

  15. HuiusSex1OmeSCAM

    • Use the Phillips #000 screwdriver to remove the 2nd 7mm screw that is holding the green panel in place.

  16. 5asNmE64J1hEgZgh

    • Using either your hand or the tweezers carefully remove the green panel from inside the headset.

  17. jaDrsXAqpDUTPioD

    • After removing the panel, use either your hands or tweezers to carefully remove and replace the volume and power buttons.

  18. Nv36cJKWpXhV6YDW

    • Lastly, remove the slide button from the headset using a pair of tweezers.

  19. vQEJMRKSuXEApuoo

    • Before beginning this guide make sure you have gathered your tools.

    • You will need The Marlin Screw Driver Set

    • It will take approximately 3 min to get assembled

    • Once your tools are gathered you may begin the guide

  20. JNDL6BbsDsddEVjZ

    • Before beginning detach the ear muff

    • Use the Metal Spudger to help detach

    • Highlighted in the red circle is what needs to be detached in order to start the guide

    • Everything will be located on the left side of The Ozeino OW810

    Spelling mishap

    Morgan G -

  21. YJ6jHsrPS1EkHZeH

    • After detaching the ear muff gather your tools

    • You will need The Marlin Screw Driver set

    • Take The Phillips #0 screwdriver to begin

  22. i4dECJHMxvafKHPC

    • Highlighted in red is the first screw needed to remove

    • Use Phillips #0 to unscrew

  23. nIJAoQsxBPggbwhV

    • Highlighted is the second screw needed to be removed

    • Use Phillips #0 screwdriver

  24. Dl6StYGIcuHWG3mJ

    • Highlighted is the third screw needed to be removed

    • Use Phillips #0

  25. 5CYvNF6ZgxASEoFa

    • Highlighted is the fourth screw needed to be removed

    • Use Phillips #0 to unscrew

  26. DWiKenBwLyG4QTqq

    • Highlighted is the fifth screw needed to be removed

    • Use Phillips #0 to unscrew

  27. bKxPAyDecyIR2ujE

    • Highlighted is the last screw needed to be removed

    • Use Phillips #0 to unscrew

    • You should have unscrewed 6 screws from the ear muff

    I would shorten this. Shortening this to, "There are six screws that need to be removed," can help the audience read through the guide faster.

    Morgan G -

  28. HN3XjXbgJRZWuQwE

    • After unscrewing the screws from the ear muff remove the piece

    • Locate circuit board highlighted

  29. Ibi5GGthvrV3mixF

    • Highlighted is the screw needed to be removed from the circuit board

    • Use Phillips #0 to unscrew

  30. Mk1CSy6eS1KKVx3j

    • Highlighted is the second screw needed to be removed

    • Use Phillips #0 to unscrew

    This step seems to be repeated.

    Morgan G -

    • After following the guide and detaching the ear muffs begging locating the plug jack and begin replacement.

    • The replacement should take approximately 10 minutes

    • To reassemble your device, follow these instructions in reverse order.

  32. uGePsimtasWYNFZP
    uGePsimtasWYNFZP
    BjVIIbOQUQSFwJxp

    • Remove both earmuff pieces

  33. aqa2ZdvHDsXbIIVE
    aqa2ZdvHDsXbIIVE
    bSCYoQIHIgoTcUaV
    kCwjaGPCFCUsHLMa

    • Unscrew all 5 3.175mm screws from each side of the ear pieces

  34. nvPAYna5VpkddLJX

    • Pull sound pieces (that go towards the ear) off both sides of the headset

  35. x5eytcSiLIUExLXC

    • Pry the silver battery off of the frame

  36. GdHlstdviEkuMqIS

    • Carefully unscrew the 2mm screw on the green circuit board

    • Pull circuit board out carefully

  37. R1NCXowWVhTsvUDK
    R1NCXowWVhTsvUDK
    qfmGqdLRVUAGQORG
    g3thTuiihFtNCMcx

    • Once circuit board is removed, unscrew the four screws on the frame beneath it

    • Repeat on other side

  38. IDC2mNHOOIL3DD6O

    • Remove the light board portion from the back of the earpiece

    • Repeat on other side

  39. jJaESDKHs5Hc2rNJ
    jJaESDKHs5Hc2rNJ
    gwTpATIXePvq6clS
    cXDNtNrcy2x3GpWn

    • Remove 3.174mm screws from the white framing

    • Repeat on other side

  40. B6J1sUeOMOJXXFqT
    B6J1sUeOMOJXXFqT
    FrNFTKVWtHuWWwxs

    • Remove the 2 4mm screws in the black piece of the headband

    • Repeat on other side

  41. tHyJQDKdaXreeXHP

    • Gently pull on the earpiece framing to remove it from the headband

    • Repeat on other side

  42. mVKEJNqlGrUZQLfC

    • Carefully remove and replace the cushioning

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Rylee

Member since: 19/02/25

571 Reputation

0 comments