iHome iD95 Screen Cover Replacement

Written By: Vincent Chan
  • Comments: 0
iHome iD95 Screen Cover Replacement

Difficulty

Moderate

Steps

17

Time Required

55 minutes - 1 hour

Introduction

If your screen cover is cracked or scratched, use this guide to replace it. The screen cover is an important part of your Home iD95 meant to protect the display from scratches, smudges, and glare.

Before starting this guide, make sure to power off your Home iD95 completely and disconnect it from any external power sources and any other devices.

  1. RxF6uNRLSRhILAai

    • Before taking apart the iD95, disconnect the AC cord from the wall socket and AC adapter from the DC jack. Remove any iPods, iPhones, and iPads attached to the device.

    • Flip over the iD95 so the bottom cover is visible and the LCD screen is facing you.

  2. EiomT3LtGUOSBasH

    • Remove the 10 mm-length, 5 mm-head screw using a Phillips #1 screwdriver.

  3. GyMkXvQjOhkQdQIR

    • Use a plastic opening tool to take out the backup battery.

  4. RR3CcHxETNGExeUJ

    • Unscrew five 17 mm-length, 6 mm-head screws using a Phillips #1 screwdriver.

  5. DdZHPEgpOMvBaVg6
    DdZHPEgpOMvBaVg6
    Xnk1dAGcXWNrHy3O

    • The bottom cover is attached to the back cover by two plastic clips. Don't use excessive force.

    • Insert a plastic opening tool between the edge of the bottom cover and the main body.

    • Gently pry the bottom cover from the body. Start anywhere along the front side of the iD95 and work your way around.

    • Grip the bottom portion of the device and gently lift the front part of the bottom cover a couple centimeters up.

  6. ZyWoqkAODmOIWiMY
    ZyWoqkAODmOIWiMY
    KXJXNaIddhK2IQTL

    • Potential for device damage: Be careful not to use too much force or you might break the plastic rings holding the side panels in place.

    • Lift up the bottom cover. Pull the side panel up first, out, and away from the device.

    • The side panels have plastic rings that will need to be lifted up and off the cylinders they are placed around.

  7. MG2QjkOWDw2xHr5M
    MG2QjkOWDw2xHr5M
    iHSAiKfBQ1dlS6MI

    • Apply the same techniques from the previous step to remove the remaining side panel.

  8. hExtSXwjywv3BOGP
    hExtSXwjywv3BOGP
    1ffurJO6N6tDKWdQ
    R45TIxycnG4y5Rlg

    • Locate the two plastic clips holding the bottom and back cover together.

    • Which clip you remove first is up to you. Rotate the device 90 degrees either left or right. Insert the flat end of a spudger horizontally between the back speaker and the back cover.

    • Place the flat end of the spudger behind one clip and pry it open. This may take repeated attempts.

    • This is the hardest step because the angle is awkward and the visibility is poor. If possible, have someone hold the device or provide lighting.

    • Once a clip has been removed, hold the bottom cover open so the clip will not fall back into place. One clip remains to be removed; you are almost there!

  9. cmXfyDxp6MwbshGX
    cmXfyDxp6MwbshGX
    OSJWmDtQKfONxFPB

    • Use the same steps to remove the remaining clip.

    • The bottom cover is still connected to the motherboard by wiring.

  10. kjOyHduEuRIYyZei
    kjOyHduEuRIYyZei
    uZG3njofrvLJUIPh

    • Use a plastic opening tool to pry off the white ZIF connector joining the wires to the motherboard.

    • Don't pull the wires. Take your time using a plastic opening tool.

  11. SQIM4pAPCwsj4YBG

    • Take out four 14 mm screws using a Phillips #1 screwdriver.

  12. dveMLYLuCnNdjscB
    dveMLYLuCnNdjscB
    SBCtrEhOYrM2ZXWR
    1doreEoffNjOAH3K

    • Use a plastic opening tool to lift the two speaker zip connectors from the logic board.

    • Do not pull on the speaker wires directly. Continue to use a plastic opening tool.

  13. CBwbfsJu2CfGUAkb

    • Lift and remove both speakers.

  14. CVfEoQlQ22Wuh2Ij
    CVfEoQlQ22Wuh2Ij
    uX1EjsDwalRwMl1d

    • Flip the logic board over.

    • Use a plastic opening tool to pry and lift the iPod adapter zip connector from the logic board.

  15. yyqOMZjRlUWGohXe
    yyqOMZjRlUWGohXe
    63rempTBIbhCZJSc

    • Use a plastic opening tool to pry and lift up the white zip connector holding the LCD screen to the buttons.

  16. 6rHoFktwUl2yZfYy
    6rHoFktwUl2yZfYy
    D5CGtCqgKmRVHkKM

    • Gently push the screen away from you to dislodge it from the plastic clip holding it in place and then pull up to remove.

  17. jWyskrOgq4lY4Yss
    jWyskrOgq4lY4Yss
    xu4VjiXqVYKCHab1

    • Use a Phillips #1 screwdriver to unscrew three, 9.5 mm-length 4 mm-head, screws holding the LCD screen to the screen cover.

    • Remove the screen cover from the LCD.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Vincent Chan

Member since: 18/04/13

19 Reputation

0 comments