Unihut Titan Pocket Keyboard Disassembly Guide

Written By: glwps
  • Comments: 0
Unihut Titan Pocket Keyboard Disassembly Guide

Difficulty

Easy

Steps

9

Time Required

25 minutes

Introduction

Unihut Titan Pocket

  1. B5qvA2IBkuAXr1Uy
    B5qvA2IBkuAXr1Uy
    fQZHoZWgXAmOyFNQ
    Edu4FF2W1e3vQsXv

    • Use a Torx T5 screwdriver to remove the 3 screws.

    • Remove the Sim tray.

    • Use a Torx T5 screwdriver to remove the 3 screws.

  2. UHehNOYVgyTVJS1g

    • Use a Torx T5 screwdriver to remove the 4 screws.

  3. 2fuFM2TOALMtsGBC
    2fuFM2TOALMtsGBC
    2T6BqTeMPpkdK1fR
    Mi1yCj4wt4RKqRfi

    • Insert the opening pick into the gap between the body and the back plate. Then open the gap so that the latch comes out.

    • There are three latches on the left and right, one on the top and two on the bottom.

  4. tMMovUnTePPXJ6p3
    tMMovUnTePPXJ6p3
    VKT5YG3hPUv4nK4A
    BAtlJe6j1CKpuQXy

    • Remove the 3 screws using a Phillips #000 screwdriver.

    • Use the opening tool to open the gap.

  5. xKWOZ4BNAkEqAWOQ
    xKWOZ4BNAkEqAWOQ
    SYgbJrSEDH5sll3P
    tQsNeovUwKXlkLOI

    • Remove the battery connector.

    • Do not remove including a black sponge. Only disconnect the silver connector.

    • Then, lift the battery.

  6. Z1ckEBBOmK3AKsyN
    Z1ckEBBOmK3AKsyN
    doBGEEEY5SZAMvrI
    DbSAEO4J52sYghuI

    • Remove the 2 screws using a Phillips #000 screwdriver.

    • Lift the top part with the pointed part of the Spudger.

    • You don't have to remove the metal sticker by just lifting the top part.

    • If the camera or earphone jack connector is disconnected during the lifting process, reconnect it.

  7. WfKLkFeuVACiMcOo
    WfKLkFeuVACiMcOo
    lWvxEZmWhd3ki6vQ
    tnLsQXDOpIKsiVQ1

    • Disconnect the 6 connectors.

    • Do not remove including a black sponge. Only disconnect the silver connector.

    • Remove the 5 screws using a Phillips #000 screwdriver.

    • Use the Spudger to lift the top of the motherboard.

  8. IMCdAo4AkPyDlPPw
    IMCdAo4AkPyDlPPw
    BJEBfMI6iPqp3gKq
    anIkmBIeIUnmBxlv

    • Remove the 5 screws using a Phillips #000 screwdriver.

    • Insert a thin thing such as a Sim pin through the hole where the screw was removed and push the keyboard out.

  9. AEEcr2sGiKfgDvLO

    • Remove the 17 plastic rivets to separate the board and keyboard.

    • Since plastic rivets cannot be reused after they are initially removed, they must be reassembled using tools such as glue.

Conclusion

To reassemble the device, follow the instructions in reverse order.

Author

glwps

Member since: 02/08/20

253 Reputation

0 comments