Smart Soldering Iron Complete Disassembly

Written By: Kara Piepenbrink
  • Comments: 0
Smart Soldering Iron Complete Disassembly

Difficulty

Moderate

Steps

16

Time Required

15 - 30 minutes

Introduction

Follow this guide to fully disassemble your FixHub Smart Soldering Iron.

For an even closer look, check out the electrical schematics here.

  1. xwG1XpPqFnOsxfNH
    xwG1XpPqFnOsxfNH
    fTxSipJXhlwxCNxY
    pNvWIHw6pIY5Lv6R

    • The color of the Touch-Safe Indicator LED provides information about the status of the soldering iron tip. Note: the soldering iron grip is always safe to touch.

    • The LED only functions when the soldering iron is connected to a power source—so use caution when handling an unplugged iron if you don't know how hot it is.

    • Blue LED: The iron has cooled below 40 °C (100 °F), and the tip is safe to touch.

    • Purple LED: When pulsing, the iron is actively heating up or cooling down. When static, the iron is in Idle Mode. The iron tip is not safe to touch.

    • Orange LED: The iron has reached the set temperature and is ready to solder. The iron tip is not safe to touch.

  2. FPgZSdHnlQFRXlFV
    FPgZSdHnlQFRXlFV
    bE6LmiRIGuFDOReO
    AcBjQqVVRIIlVKof

    • The sliding power switch has a built-in color indicator for each position:

    • Orange: ON

    • Blue: OFF

    • Slide the power switch to the blue OFF position.

    • The LED will turn purple and pulse to show the iron is powering down.

    • Leave the soldering iron connected until the indicator ring turns blue, indicating it's now safe to touch the soldering iron tip.

    • Remember: The LED only functions when the soldering iron is connected to a power source—so use caution when handling an unplugged iron if you don't know how hot it is.

  3. aeN4g2B3bLXRcEpF
    aeN4g2B3bLXRcEpF
    VVaZA211DeIOgsvT

    • Disconnect the iron's USB-C cable from your power source.

  4. XNeVhTUxBhVcVG1e
    XNeVhTUxBhVcVG1e
    YQmDTLpTBCQGTJUX
    MjhjdOGOHqYsmLZB

    • Twist the blue cable collar counter-clockwise and pull up to release it from the iron.

  5. MxXxLfTqNZW2FQNv
    MxXxLfTqNZW2FQNv
    1XOor3gfTtLNJjD4

    • Disconnect the USB-C cable from the Smart Soldering Iron.

  6. GvWFlkbZqM1w4k5A
    GvWFlkbZqM1w4k5A
    AuSlQvWQqQUJ1pwe

    • Hold the iron from both ends and pull to remove the cap.

  7. EfXTlLNNeKUJtwyn
    EfXTlLNNeKUJtwyn
    FReuNWlTSC2rVmZu

    • Use a Phillips screwdriver to remove the 8.0 mm‑long screw at the bottom of the opening of the soldering iron cap that secures the cap tip and clip spring to the cap.

    • You will need a long-shaft screwdriver to be able to reach the screw inside of the soldering iron cap.

  8. KuPS43NaBug2XwWR
    KuPS43NaBug2XwWR
    BDMhVxULht5HZJ2R
    tlCl6lCEZFfstYsF

    • Pull upward on the cap tip to remove it from the cap.

    • During reassembly, fit the iron prongs at the top of the cap into the holes at the bottom interior of the cap tip.

  9. BmBKmd3ISh61fAFs
    BmBKmd3ISh61fAFs
    EmtoXTNCcDAw5KQB
    exF5fax6T4DLH3OH

    • Pull up from the bottom of the cap spring clip.

    • Pull the ends of the spring clip straight out through the holes in the cap to remove it.

  10. iBYKUgChxyVZltFx
    iBYKUgChxyVZltFx
    UVtIViYWR6genZSh

    • Make sure the tip has fully cooled before touching it.

    • Firmly grasp the base of the tip and pull it away from the front of the iron handle to remove it.

  11. MxJhRBShZqRShkiI
    MxJhRBShZqRShkiI
    F45ulMHmEOtdlMRb

    • Use a Phillips screwdriver to remove the three blue 3.4 mm‑long screws securing the blue end cap.

    • Use a Phillips screwdriver to remove the one black 3.4 mm‑long screw at the base of the enclosure.

  12. TfVYLVbgOqgolWGL
    TfVYLVbgOqgolWGL
    aMnquCHBTbHq2AqJ

    • Pull to remove the blue end cap from the rest of the iron handle.

  13. ddcOvi1eeCqVOJHa
    ddcOvi1eeCqVOJHa
    LiSwJQXycfPSf6Ns

    • Remove the blue and orange power switch.

  14. HaeyhSxDcfhCSFiP
    HaeyhSxDcfhCSFiP
    LWbKendJcs3XaKO4
    A3dXVRadOY2KgxAp

    • Grasp the end of the main board that sticks out from inside of the soldering iron handle.

    • Pull to slide the main board out of the handle.

    • When reassembling your iron, make sure to insert the main board with the shiny iron auxiliary port end first.

  15. aUAjZaUEtt4tQ5cD
    aUAjZaUEtt4tQ5cD
    THvTsUtkhLPFA5mU
    KVjqLWlsZtyhNKfw

    • Twist the iron enclosure below the grip and pull to separate the grip from the enclosure. Just the grip remains.

  16. fJSA1GmIpYJETQD4

    • Your Smart Soldering Iron is fully disassembled!

Conclusion

To reassemble your Smart Soldering Iron, follow these instructions in reverse order.

Repair didn't go as planned? Try some basic troubleshooting, or ask our Answers community for help.

Author

Kara Piepenbrink

Member since: 31/05/24

3535 Reputation

0 comments