Samsung Galaxy S24 Ultra Back Cover Replacement

Written By: Spencer Pennington
  • Comments: 1
Samsung Galaxy S24 Ultra Back Cover Replacement

Difficulty

Moderate

Steps

15

Time Required

20 - 30 minutes

Introduction

Use this guide to replace the back cover in your Samsung Galaxy S24 Ultra.

  1. PX6ZWXUGv6lqHVlB
    PX6ZWXUGv6lqHVlB
    nbHuWH42sGPdRPRW

    • Allow your phone's battery to drain below 25%, as a charged lithium-ion battery is a potential safety hazard. If your battery is swollen, take appropriate precautions.

    • Unplug any cables from your phone.

    • Hold the side key and the volume down button, then select "Power off" to turn off your phone.

  2. eoeLhYvZHFWVyJLP

    • Heat an iOpener and apply it to the right edge of the back cover for two minutes.

    • You may use a hair dryer, heat gun, or hot plate instead, but be careful not to overheat the phone—the display and internal battery are susceptible to heat damage.

  3. dXqkmHBZeVPyOuSU
    dXqkmHBZeVPyOuSU
    PyHHYrood3VP4x5t
    OPLd1nubMoJcYqbs

    • Apply a suction handle to the back cover, as close to the center of the right edge as possible.

    • Pull up on the suction handle with strong, steady force to create a gap between the cover and the frame.

    • If you have trouble creating a gap, apply more heat to further soften the adhesive. Follow the iOpener instructions to avoid overheating.

    • Insert an opening pick into the gap.

  4. IfaaLTVGCcCZuQSl
    IfaaLTVGCcCZuQSl
    o6FRoEyVIyCBSW3Z
    Yhi2KOKeADjkfGvV

    • Slide the pick back and forth along the right edge to separate the adhesive.

    • Leave the pick inserted near the bottom right corner to prevent the adhesive from resealing.

  5. SEwAHBisYqJBLM1L

    • Apply a heated iOpener to the bottom edge of the back cover for two minutes.

  6. 2SFSHTRLeqgrH4lu
    2SFSHTRLeqgrH4lu
    lmjEhsscFoSvtbhw
    RUoTEYoG5xUyEKHH

    • Insert a second opening pick next to the first one, near the bottom of the right edge.

    • Rotate the opening pick around the bottom right corner to separate the adhesive.

  7. FM4W5gn6uQHHxwnR
    FM4W5gn6uQHHxwnR
    auiMelVFREHofWYU

    • Slide the opening pick along the bottom edge to separate the adhesive.

    • Leave the pick inserted near the bottom left corner to prevent the adhesive from resealing.

  8. ExIixemEEXUokOHE

    • Apply a heated iOpener to the left edge of the back cover for two minutes.

  9. FuCZKH5aQQHvxdso
    FuCZKH5aQQHvxdso
    LiDDeZedXlnBuWki
    N2wPNcgBAHtYHMXn

    • Insert a third opening pick next to the second one, near the left side of the bottom edge.

    • Rotate the opening pick around the bottom left corner to separate the adhesive.

  10. vXnjCO2niySjhyTs
    vXnjCO2niySjhyTs
    ApxDAlLyLaKnpfgL

    • Slide your opening pick along the left edge to separate the adhesive, stopping before you reach the power button.

    • Do not insert the pick more than 4 mm to avoid damaging the antenna cable.

    • Leave the pick inserted near the power button to prevent the adhesive from resealing.

  11. 1LrEv6ISBgcMgXdN

    • Apply a heated iOpener to the top edge of the back cover for two minutes.

  12. DPCEkMKoq2qIbnmT
    DPCEkMKoq2qIbnmT
    kWEemRVuZTjhTggP
    DiLaNuXprfMWfc3y

    • Insert an opening pick in the gap at the top of the right edge.

    • Rotate the opening pick around the top right corner to separate the adhesive.

  13. ENLFTt4XUhPmlCZG
    ENLFTt4XUhPmlCZG
    VZZl32bJLVfyMCEt

    • Slide the pick along the top edge to separate the adhesive.

    • Do not insert the pick more than 4 mm to avoid damaging the sensor or camera near the top edge.

  14. PA1yL4WNMeEOFCwH
    PA1yL4WNMeEOFCwH
    RrUJrPgfbqJoRHPv
    IpCVfVtDmpglsbBw

    • Slide the pick around the top left corner and down the left edge to separate the remaining adhesive.

    • Do not insert the pick more than 4 mm to avoid damaging the cameras.

  15. Mned3U6WyfkSqJ2D
    Mned3U6WyfkSqJ2D
    qowbZ1J2jsGr2X1V

    • Grab and remove the back cover.

    • If your cover is still sticking to the frame, slide an opening pick around the edges to separate any adhesive that may have resealed.

    • During reassembly:

    • This is a good point to power on your phone and test all functions before sealing it up. Be sure to power your phone back down completely before you continue working.

    • Remove any adhesive chunks with a pair of tweezers or your fingers. Apply heat if you're having trouble separating the adhesive.

    • If you're using custom-cut adhesives, follow this guide.

    • If you're using double-sided tape, follow this guide.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

Author

Spencer Pennington

Member since: 09/09/23

13296 Reputation

One comment

S34ultrs model

Boikanyo Motshegare -