Numpad with Keyboard Removal

Written By: Alex Diaz-Kokaisl
  • Comments: 1
Numpad with Keyboard Removal

Difficulty

Moderate

Steps

6

Time Required

No estimate

Introduction

Prereq for removing the keyboard and numpad.

  1. FyZqYQXlGGSUVdfO
    FyZqYQXlGGSUVdfO
    ddbQkHnXk5QEvLfj

    • Unplug all cables and fully shut down your laptop.

    • If your repair requires a spudger, a T5 Torx, or a Phillips screwdriver, you can use the included Framework screwdriver. Whichever works best for you!

    Step 1 is not really necessary, it is up to you. The keyboard, trackpad, etc, can be hot-swapped, meaning you can remove them at any time when the laptop is off OR on. The keyboard and the macropad/numpad/spacers/LED matrixes all lose power anyways when the trackpad is slid out of its resting spot. Turning off the power or doing a restart may help if some software of yours isn't happy with you swapping your keyboard on the fly.

    ChazIsBuns -

  2. oRA2BGYySG6cv4UI
    oRA2BGYySG6cv4UI
    EjHQwVWhreadODGC
    Qd4HyChkTncRj6NB

    • Use your fingers to slide the touchpad spacer toward the bottom edge of the laptop and unclip it.

    • If you're having trouble, check if the corresponding Input Module latch is properly unlocked.

    • Lift the touchpad spacer off the laptop and remove it.

  3. PIQuXTPBOmiCmpTP

    • Repeat the same procedure for the other touchpad spacer.

  4. XUyEDC4iKWYV5Tnt
    XUyEDC4iKWYV5Tnt
    pTmsgnLnOsotLW2D
    IAOYbMHag2mlLGT6

    • Use your fingers to slide the touchpad toward the bottom edge of the laptop and disconnect it.

    • If you're having trouble, check if the Input Module latches are properly unlocked.

    • Lift the touchpad and remove it.

    • During reassembly, perform the following:

    • Place the touchpad flat on its cutout so its clips are properly aligned.

    • Press the touchpad down and slide it into place so it lines up evenly with the bottom edge of the laptop.

  5. EMiltNMDCZ2ZfrqP
    EMiltNMDCZ2ZfrqP
    kI1lOpjnUTZDpfZt
    5UtiQGpQXVRbA4QM

    • The keyboard is held in place with strong magnets. Apply gradually increasing force to avoid having the keyboard violently eject.

    • Grip the two pull tabs along the bottom of the keyboard.

    • Lift the pull tabs until the keyboard magnets release.

    • Remove the keyboard.

    • During reassembly, make sure the keyboard is seated properly on its alignment pegs and sits evenly with the edges of the laptop.

  6. F6EtPOhQyBDv3K5Q
    F6EtPOhQyBDv3K5Q
    fJDM6TD5UaZ5BvkI
    xeLqBn636iKVEMk2

    • The numpad is held in place with strong magnets. Apply gradually increasing force to avoid having the numpad violently eject.

    • Grip the pull tab at the bottom of the numpad.

    • Lift the pull tab until the numpad magnets release.

    • Remove the numpad.

    • During reassembly, make sure the numpad is seated properly on its alignment pegs and sits flush with the edges of the laptop.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Alex Diaz-Kokaisl

Member since: 16/01/22

151892 Reputation

0 comments