LG Front Load Washing Machine Control Panel Replacement

Written By: Bill Gilbert
  • Comments: 0
LG Front Load Washing Machine Control Panel Replacement

Difficulty

Moderate

Steps

11

Time Required

15 - 30 minutes

Introduction

Use this guide to replace the control panel in your LG front load washing machine.

  1. IWjgsUtZOIuShVqa
    IWjgsUtZOIuShVqa
    cmisDLhhQ1ZspJJT

    • Before you begin your repair, perform the following:

    • Turn off the main water supply

    • Unplug your washer

    • Disconnect all water connections at the rear of your washer

  2. a1CEVEuZVuhsJs3v
    a1CEVEuZVuhsJs3v
    s1Dx6pURHR66tbUG
    WMesicEUoODuO1DI

    • Remove the screw(s) securing the top panel brackets to the back panel.

    • You don't need to remove the screws securing the brackets to the top panel.

  3. MXS5aiRAHxRbjTgD
    MXS5aiRAHxRbjTgD
    BqIF6FiMQVaOIZZQ

    • Slide the top panel towards the rear of the device to disconnect its clips.

  4. vk2XTwmpQAn5SSnW
    vk2XTwmpQAn5SSnW
    mKqTwIkkot2M6aDA

    • Tilt the top panel upward to completely disconnect it from the chassis.

    • Remove the top panel.

  5. 4sgimkxaXD3ejSwK
    4sgimkxaXD3ejSwK
    bkCBDPSK6YgGYTcr

    • Pull the detergent drawer away from the chassis as far as it will go.

  6. P6jShSDIRVTufbKa
    P6jShSDIRVTufbKa
    XRPBgqFyjRWpSKkn
    oCBTknIPcxBXF3VM

    • Press down on the "Push" button to disengage the clips securing the detergent drawer.

    • Pull the drawer out of its slot on the chassis and remove it.

  7. ZggChMox2CHdQQKT
    ZggChMox2CHdQQKT
    WevyfGPPM3VaJVqy
    6etGaxcS1KQCdwr1

    • Disconnect the connectors attached to the control panel.

    • Always grip cables by their connectors and not the wires themselves.

  8. wyfktcrXysd6MEbF
    wyfktcrXysd6MEbF
    xVcjUMUvZQ1KywIX

    • Remove the screw(s) securing the control panel to the top edge of the chassis.

  9. HtPUiKkN5cVYWnLd

    • Remove the screw(s) securing the detergent dispenser.

  10. NjYZQqTADGvZuhyI
    NjYZQqTADGvZuhyI
    JIrrrvJmMJUppOF5
    GQ3x4wTaWu3iwVOS

    • Use a flathead screwdriver, or a pry tool, to unclip the control panel from the chassis.

  11. sOFWfj6q1QcVriGT
    sOFWfj6q1QcVriGT
    jASuxq6RmJTE5JZB
    Do5pLK3NYMAwl1sB

    • Remove the control panel, making sure to thread any cables through the chassis.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Bill Gilbert

Member since: 30/06/22

35117 Reputation

0 comments