JBL Charge 2 Plus Bottom USB Ports and Aux Port Replacement

Written By: John Reynolds
  • Comments: 18
JBL Charge 2 Plus Bottom USB Ports and Aux Port Replacement

Difficulty

Moderate

Steps

6

Time Required

15 minutes

Introduction

This guide can be used to replace your USB ports and aux cable.

  1. JfSWgo2C6HR1CSIH

    • Flip the device so the bottom is facing you.

    • Remove the bottom pad with a nylon or metal spudger.

  2. PVZRyWwvKfLOxMOX
    PVZRyWwvKfLOxMOX
    HXVP5jgspvx1lNmd

    • Remove the 4 screws that hold the white cover.

  3. NRWXQckmdTIHThDJ

    • Slide under the cover and remove it.

  4. c6QhOFweLvmWXsNr
    c6QhOFweLvmWXsNr
    BTFtRGXEKaUJySjb

    • Remove the one screw holding the circuit board.

  5. 2DGCWKpASfjB4Ljs

    • Pry the board with the plastic opening tool.

  6. 2MKlonMQ4XKoevOg
    2MKlonMQ4XKoevOg
    bEspuO6esvRJSpQe

    • Slide the ribbon gently out of the connector.

    What the name of the white ribbon and where can i buy another mine on my jbl got damaged

    Jose Lopez -

    From where can I get the micro usb port. Its broken…or what's its called?

    Shreyansh Badola -

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

John Reynolds

Member since: 16/10/15

3206 Reputation

16 comments

Hi! I need the mini usb piece but I don´t know were I can buy it, it is not like the mobile one´s! Please help me!

Thanks

Clash Ofclans -

Just having the same issue with the internally broken micro-usb connector. Is it standard, or something special? Thanks!

egyusza -

I think it is not normal, if you can find it please contact me! Thanks

Clash Ofclans -

I also need to replace my usb connector, has anyone found out where to get one?

Rick -

need the micro-usb aswell

hellgrenmicke -

My jbl charge 2+ is different, after removing the plastic thing in step one there aren't any screws

Juan Sanchez -

[|same too at mine :-(]

Eki mako -

I tried step one and was only able to peel off the rubber base exposing the double sided tape. I do not see the cover as shown in step 2. Any help is greatly appreciated. Thanks!

Trevor Tremblay -

Same case here… :-(

Eki mako -

Hi, are There different versions of the 2+?

i don’t have screws at the bottomplate and it looks different…

Eki mako -

How can i make the sound come back?

Tara Ruesta -

where do i get the part?!?!? Torn down the speaker allrdy..

Hannu “Hulluporo” Albrecht -

The easiest thing is to replace the whole circuit board, I’d try ebay and get something like this https://www.ebay.com/itm/JBL-CHARGE-2-SP...

fdsajky675 -

Has anyone tried to install a USB-C in a JBL Charge 2+?

Christopher Cunningham -

I‘ve bought the Micro usb Port from Ebay and got as far as opening and getting out the board. What I‘m not able to see though using a magnifying glass is if only the ports 4 legs are soldered into the circuit board or if the 5 small contacts on the port need to be soldered to the boards contacts too. Because that‘s something I would not be able to do with my limited tools which are not suitable for such a delicate job. If you can answer this question l would appreciate that.

Jürgen Walter -