Huawei P10 Lite Back cover Replacement

Written By: Dominik Schnabelrauch
  • Comments: 18
Huawei P10 Lite Back cover Replacement

Difficulty

Moderate

Steps

4

Time Required

15 - 25 minutes

Introduction

Use this guide to replace the back cover of your Huawei P10 Lite.

  1. YqiUymRKMTYinZcE
    YqiUymRKMTYinZcE
    1x5qv4HPtVGSmvpD
    byJlAME6WaXCgGa2

    • Insert the tip of an opening pick between the back cover and the mid frame and slide it around the phone, to cut the adhesive.

    • Using a suction handle to lift the back cover may help to get an initial gap for the opening pick to put in.

    • If the adhesive is hard to cut, use an iOpener to loosen it.

    Mit dem Saugnapf die Rückseite anheben hilft ungemein…

    Matthias Eberle -

    Had to use blue wedge tool to wedge open bottom plate from the rim part in order to then use the tip of the blue opening pick under the back plate to then cut the glue. It’s like placing a pie server or knife under the plate once there’s a gap between the rim and the back plate.

    Jane -

    Be careful, there’s a cable to fingerprint sensor, very close to the edge (see pictures below)… It’s very easy to cut it through with the pick, as I just learned :)

    dambig -

  2. F5lCy2LZ2xfWDDqg
    F5lCy2LZ2xfWDDqg
    Na6gp15IRbPSW3Ll
    2xyqfXZApukGpaZe

    • After you cut the adhesive on every edge, twist your opening pick, to separate the rear cover from the phone.

    • Flip the rear cover over to the right side of the phone.

  3. oPLqQqGCxyiCQ6oZ
    oPLqQqGCxyiCQ6oZ
    gZgRjiB2CuBip3Xu

    • Use a pair of tweezers to remove the sticker.

    • Remove the two Phillips #00 screws.

    • Remove the four 2.5 mm Phillips #00 screws.

    Schritt 3 und 4 kann man sich komplett sparen. Wozu auch. Kann gleich mit Schritt 5 weitergemacht werden, zuvor einfach das Flachbandkabel vom Fingerabdrucksensor an der Rückabdeckung abklemmen und fertig.

    Bobby mcgee -

    There are four silver screws and two black to be removed.

    Jane -

    Translate what Bobby mcgee said:

    Step 3 and 4 can be completely ignored. What for? You can continue with step 5, just disconnect the ribbon cable from the fingerprint sensor on the back cover and you're done.

    Antonio Sun -

    However, the reason step 3 and 4 should not be skipped is Step 6 — Use an iOpener to loosen the adhesive beneath the battery. I.e., the adhesive cannot be easily removed without heat, however, that heat might damage the electric chips. Thus they’d better be removed first.

    Antonio Sun -

  4. jMQb6f2oPStGtZUm
    jMQb6f2oPStGtZUm
    QdMRkHKjOFsRwEGW

    • Use tweezers to remove the mainboard shield.

    • Use the flat end of a spudger to disconnect the finger print sensor flex cable.

    • When reassembling apply new adhesive where it is necessary.

    Welchen Klebstoff soll man verwenden?

    josef navratil -

    Hallo Josef,

    sollte bei deinem Ersatzteil kein Klebstoff oder Klebeband dabei gewesen sein, kannst du dünne Streifen Doppelseitiges Klebeband verwenden. Es gibt für das Huawei P10 Lite auch schon zugeschnittene Klebestreifen zu erwerben, hierbei gilt aber je nach Händler Rezessionen zu lesen, ob die Klebestreifen auch wirklich halten.

    Dominik Schnabelrauch -

    Note that there is a copper-colored sticker to lift up near the flat cable connected from the phone the finger pad. Lift the main board plate (shield) up SLOWLY from the camera side to the other end as the plate is wedged in place.

    Jane -

    what adhesive is recommended? thanks

    darren -

    Hi darren,
    pre-cut adhesive would be the best solution if you can source it. Otherwise a two-sided adhesive tape or carefully used E6000 adhesive glue will be your friend.

    Tobias Isakeit -

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Dominik Schnabelrauch

Member since: 23/11/16

224647 Reputation

6 comments

Great guide, but how do I move the fingerprint sensor to the new cover?

mela ross -

You need to warm the adhesive so it can be loose

Adwell Cellular -

What adhesive should I use? Thank you!

Calin GV -

Nice guide! Thanks! I got a little question about the coloring of the back panel. What kind of coloring is it? Is it a coating you can take off, or is it more like a layer of paint you can scrape off? I am wondering, because I want to clear the back of my Huawei P10 lite. I hope it’s possible though.

Daan -

Can you send me please back cover.

I'm from Nepal .

Md Usman -

Samsung galaxy core repairing karana hai

Gaindlal -