HP Photosmart D110a Replacing the Scanner Light Replacement

Written By: Tim Wise
  • Comments: 1
HP Photosmart D110a Replacing the Scanner Light Replacement

Difficulty

Moderate

Steps

10

Time Required

15 - 30 minutes

Introduction

  1. BVK3dDZoWqsjwJAw

    • Pull down both front panels to open the printer. Lift the scanner flap upward by pulling down on it; there are two mouth pieces that need to be pulled down.

    • Adjust the flap covering the scanner upward, as shown.

  2. L5DIt5JKwbZWCKx2

    • Pull the scanner flap gently away from the printer to release its two clips.

  3. lY1tygquQaAcy1Fb

    • Locate the three screws on top of the printer.

    • The orange circle shows a fourth screw located behind the power panel. Ignore this one for now, as directions to remove this screw are in Step 5.

  4. NxYZVH4FWoWSDokv
    NxYZVH4FWoWSDokv
    Bxp2AiL4IFtvESIb
    ZMwdOTEj5AJu5mjw

    • Using a T-9 screwdriver, remove the three screws from the printer's top.

  5. xeTUebAQouQGZFWu
    xeTUebAQouQGZFWu
    aucI5mjPpt6aWyLl

    • To remove the power button panel:

    • Reach inside the printer's front opening.

    • Press the small clip behind the power button.

    • A picture of the power button panel removed is provided to show the location of the clip that needs to be pressed.

    • Pull the panel out from right to left.

  6. 2AQMWI3AS4ZoBEBu
    2AQMWI3AS4ZoBEBu
    OBbdI1Wj3LbMwwHD

    • Remove the fourth screw, which was covered by the power button panel.

    • Do not try and torque the screw from an angle. This will ruin the screw's head, and make it even more difficult to remove the screw. Only remove it as already described.

    • This screw is placed awkwardly. We found holding a T9 bit in a pair of needle nose pliers gave us enough leverage to pull it up.

  7. vO1oP3QaMFaQkVBo
    vO1oP3QaMFaQkVBo
    4C1oCXuFxyFqkWg3
    vtETonPH5wa2IkPR

    • With a partner's help:

    • Have one person lift the hood 2-3 inches.

    • Have the other person disconnect the three cables from the motherboard (the green PCB) to the hood by gently pulling upward on them.

    • Remove the hood completely.

  8. BpOA5JNa3L6eXjwU
    BpOA5JNa3L6eXjwU
    VurxScFYo3Uoxybb
    A6RmbZxYLHG4OdLD

    • Remove the single T-9 screw from the hood's underside, as shown.

  9. rGCkPCf3vR4OcGKP
    rGCkPCf3vR4OcGKP
    BkQKagKIuypOGFWA

    • With the screw removed, separate the two pieces of the hood by lifting it vertically.

    • Only lift the the top piece enough so that there is no tension applied to the ribbon cables shown.

    • Carefully pull down the white ribbon cable through the top piece of the hood.

  10. yaGvhYIlrtYiIuST
    yaGvhYIlrtYiIuST
    ght2idMErPkFQNNY

    • Separate the hood pieces while keeping the black ribbon cable connected. Rest the scanner piece carefully to avoid stressing its ribbon cable.

    hi, can assist me on how to replace encoder strip hp d110a. thanks

    Rufai Yusuf -

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Tim Wise

Member since: 01/04/11

173 Reputation

0 comments