Google Pixel 9 Pro Fold Flip Battery Replacement

Unplug all cables from your phone and completely power it down.

Apply a suction cup to the screen, as close to the center of the bottom edge as possible.

Pull up on the suction cup with strong, steady force to create a gap between the screen and the frame.

Insert an opening pick into the gap.

Slide the opening pick around the bottom right corner and up the right edge of the screen to separate the adhesive.

Slide the pick around the top right corner and stop before the front camera.

Pull the opening pick out so only the tip is under the screen.

Slide the opening pick across the top edge of the screen until you're past the front camera.

Push your pick to its original depth before continuing.

Slide the opening pick around the top left corner and stop about two‑thirds down the left edge of the screen.

Pull the opening pick out to a 2 mm depth and rotate the pick around the bottom left corner to separate the remaining adhesive.

Lift the right edge of the screen and swing it over the left edge of the phone, like opening a book.

Prop up the screen with your suction handle or a clean, sturdy object.

Use a Torx Plus 3IP driver to remove the 2.2 mm‑long screw securing the display cable bracket.

Use a spudger, or your fingers, to lift the display cable bracket enough to access the press connector underneath.

Use the point of a spudger to pry up and disconnect the display cable press connector.

Lift the screen off the frame and remove it.

Use a Torx Plus 3IP driver to remove the 2.0 mm‑long screw securing the battery bracket.

Use tweezers, or your fingers, to move the battery bracket out of the way of the battery press connector.

Use the point of a spudger to pry up and disconnect the battery press connector.

Use tweezers, or your fingers, to remove the rubber block covering a screw on the top board.

Use a Torx Plus 3IP driver to remove the two 2.2 mm‑long screws securing the top interconnect cable bracket.

Use tweezers, or your fingers, to remove the top interconnect cable bracket.

Insert the point of a spudger under the top right corner of the top interconnect cable press connector, near the golden marker.

Pry up and disconnect the top interconnect cable press connector.

Use a Torx Plus 3IP driver to remove the two 2.2 mm‑long screws securing the bottom interconnect cable bracket.

Use tweezers, or your fingers, to remove the bottom interconnect cable bracket from the lower board.

Insert a spudger under the right edge of the bottom interconnect cable press connector.

Pry up and disconnect the bottom interconnect cable.

Insert a SIM eject tool, bit, or straightened paper clip into the SIM card tray hole and press firmly to eject it.

Remove the SIM card tray.

Use the tip of a spudger to lift up the top right corner of the lower board and unclip it from the frame.

Remove the lower board.

Slide the flat end of a spudger under the flip battery cable to separate the adhesive.

Use tweezers, or your fingers, to lift the flip battery cable connector and fully separate it from the frame.

Use your fingers to peel both edges of the flip battery pull tabs off the battery.

Unfold your phone and flip it so the inner screen is facing upward.

Use a hair dryer, or a heat gun, to heat the section of inner screen behind the flip battery (the side with the SIM card cutout) until it's barely too hot to touch.

Fold your phone and turn it so the flip battery is facing up.

Pull up on alternating sides of the pull tab to slice through the adhesive on the upper half of the flip battery, stopping once you get to the top edge.

Apply a few drops of isopropyl alcohol (>90%) under the bottom edge of the flip battery.

Lift the bottom edge of the phone to let the isopropyl alcohol flow under the battery.

Wait one minute for the alcohol to soften the adhesive.

Apply a suction handle to the center of the flip battery.

While securing the phone with one hand, pull up on the suction cup with strong, steady force to separate the flip battery from the frame.

Remove the flip battery.

Congratulations on completing disassembly! The remaining steps will show you how to reassemble your device.

Use tweezers, or your fingers, to remove the old flip battery adhesive from the frame.

Apply isopropyl alcohol (>90%) and use a coffee filter or microfiber cloth to clean any adhesive residue.

Place the flip battery cable and connector adhesives over the frame, using the white outlines to confirm their orientation.

Peel the adhesive strips off their liners and place them over their respective spots on the frame.

Use the flat end of a spudger, or your fingers, to press down on the adhesive strips to adhere them to the frame.

Peel the main flip battery adhesive strip from its clear liner.

Align the top edge of the adhesive strip with the top edge of the battery recess.

Lay the adhesive strip on the frame.

Use the flat end of a spudger, or your fingers, to press down the individual adhesive strips to adhere them to the frame.

Use the pull tab to peel the colored liner off to expose the adhesive.

Peel off the colored liners on the flip battery cable and connector adhesive.

Align the top edge of the flip battery with the top edge of the battery well.

Lay the battery over the frame.

Press down along the perimeter of the flip battery to adhere it to the frame.

Press down the flip battery cable and its connector to adhere it.

Let the phone sit for an hour for the adhesive to cure.

Press the bottom edge of the lower board against the frame at a downward angle to engage its metal spring.

Press the board flat to the frame, making sure the screw holes are aligned.

While holding the lower board in place, reinsert the SIM card tray.

Reconnect the bottom interconnect cable press connector.

Place the bottom interconnect cable bracket on the lower board and align its screw holes.

Use a Torx Plus 3IP driver to install the two 2.2 mm‑long screws securing the bottom interconnect cable bracket.

Reconnect the top interconnect cable press connector.

Place the top interconnect cable bracket on the top board and align its screw holes.

Use a Torx Plus 3IP driver to install the two 2.2 mm‑long screws securing the top interconnect cable bracket.

Place the rubber block over its spot on the top board and press it down.

Reconnect the flip battery press connector.

Lay the flip battery bracket over the press connector and align the screw holes.

Use a Torx Plus 3IP driver to install the 2.0 mm‑long screw securing the battery bracket.

Use a spudger, or your fingers, to remove the old bottom left outer screen adhesive.

Use isopropyl alcohol (>90%) and a coffee filter or a microfiber cloth to remove any adhesive residue.

Before removing any liners, check if the bottom left outer screen adhesive matches the frame.

Peel the bottom left outer screen adhesive off its clear liner to expose the adhesive.

Put the adhesive into place on the frame.

Use the flat end of a spudger to press along the adhesive strip to adhere it to the frame.

Before removing any liners, check if the perimeter outer screen adhesive matches the frame.

Peel away the top half of the new adhesive strip from its clear liner and keep it folded.

Align the top half of the adhesive over the frame, using the corners as reference points.

Place the adhesive on the frame.

Use the flat end of a spudger, or your fingers, to press down the top edge of the adhesive and adhere it to the frame.

While peeling away the rest of the clear liner, slowly lay the rest of the adhesive over the perimeter of the phone.

Use the flat end of a spudger, or your fingers, to press down the rest of the adhesive and adhere it to the frame.

Use the tip of a spudger to pry up the segmented tab on the bottom left corner of the large blue liner.

Lift the tab and peel off the large blue liner to expose the secondary liner.

Support the screen with your hand or prop it up on something sturdy.

Reconnect the outer screen cable press connector.

Reinsert the outer screen cable bracket clip under the frame and align its screw hole.

Use a Torx Plus 3IP driver to install the 2.2 mm‑long screw securing the display cable bracket.

Remove the blue liner from the bottom left outer screen adhesive strip.

While holding the screen above the frame, separate one of the secondary liner's pull tabs at the bottom left corner.

Still holding the screen, peel off the secondary liner to expose the adhesive.

Align the outer screen over the frame and press it into place.

Press along the perimeter of the outer screen to adhere it to the frame.

Let the phone sit a few hours for the adhesive to cure.