Fujifilm FinePix HS30EXR Discharge Flash Replacement

Written By: Haden Calvert
  • Comments: 1
Fujifilm FinePix HS30EXR Discharge Flash Replacement

Difficulty

Difficult

Steps

16

Time Required

35 minutes

Introduction

This guide serves to help the user replace the flash bulb.

Warning: The replacement of the flash bulb requires great care, as any force could damage the frame or any internal cables/wires that may be essential to the camera's function. To avoid damage, treat the frame with care when prying it off, and treat and wires or cables with care as well.

  1. TX4JMActQPfIidXM

    • Flip the camera so that the bottom is facing upwards.

    • With the Phillips #00 screwdriver, remove all four screws.

  2. ywDCxRwuWEXdJTY1

    • Flip the camera so that it is now on the right side.

    • With the Phillips #00 screwdriver, remove all four screws.

  3. iQT6TUwXEdJfFL5j

    • Flip the camera so that it is now on the left side.

    • Move or remove the flap hiding the camera ports.

    • With the Phillips #00 screwdriver, remove all screws.

  4. kxBca6Ir2twMFFC5

    • Flip the camera so that it is now on the top side.

    • With a spudger, pry off the highlighted metal piece of the camera.

    That's a bit misleading it's a spring clip at the bottom of the hot shoe

    Colin Head -

  5. r2rocMG14fKjdtjq

    • With the Phillips #00 screwdriver, remove all four screws.

  6. 4iSKOFPpTkDCAHY5

    • Pull the LCD screen up and out of the way.

    • With the Phillips #00 screwdriver, remove the screws.

  7. CiNmmNZtwWioIoUg
    CiNmmNZtwWioIoUg
    rctlgQn3frxmrMie

    • With a spudger, pry off the frame.

    • If the frame does not easily dislodge after a few attempts, ensure that all screws are taken out.

  8. j2Nq5bHSUErUuSYI

    • Slowly and carefully pull the frame away to have a better view of the inside.

  9. kBqwjGdc5faIpWWW

    • Peel back (or off) the black tape to expose more of the inside of the camera.

    • Flip the white switch of the highlighted chamber up, and that should unlock the ribbon cable from its compartment.

    • To see if this worked, gently pull the ribbon cable out of the compartment. It should come out without force.

  10. xYnDQmVcEnsH1oSR

    • Disconnect the ribbon cable.

  11. gpxWT2UKunDQkSkH

    • With the Phillips #00 screwdriver, remove all five screws.

    • Remove the metal casing.

  12. lIlDH36GlGcnbydn

    • With the Phillips #00 screwdriver, remove all screws.

  13. 5IeZcSsjic5rGhFl

    • Ensure the four ribbon cables are disconnected from the motherboard.

    • Be aware, one is under the black tape.

  14. atbstk6gMCnlLU3U

    • Begin desoldering all four highlighted areas.

  15. UaIGaRbXOHCqpDaQ

    • Remove the motherboard.

  16. DMCs2Lg41SH4IDeg

    • Remove the discharge flash by giving it a light tug. It is held in place with glue.

    • Replace the old flash bulb with a new one, and begin the reconstruction of the device.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Haden Calvert

Member since: 22/10/18

100 Reputation

0 comments